Termékek decortex premium (10)

Smooth acrylic revetment with polysiloxanes high quality for the protection and decoration of all types of surfaces of concrete, exterior brickworks, renovation of monocoat mortars on facades, etc. Paint with a coating protect that provides an excellent protection against a wide range of fungus and algae. Permeable to water vapour. Waterresistant product, impermeable to liquid water.

Protech Fix AC-Therm Water-based anti-condensing wall covering, with excellent fixing and anchoring properties, with good coverage based on high penetration acrylic resins, 3M Glass Bubble, pigments, fillers and covering fillers. Suitable as an anti-condensation fixative primer, prior to painting or coating the plaster with anti-condensation paints or plasters (-THERM). Ideal for interventions on walls with mucilage deposits, bacterial phenomena and moulds. Due to its low thermal conductivity, it is particularly suitable for solving mould problems. It can be applied on any plaster (rustic, civil, plaster, dry mortar, plasterboard, concrete, prefabricated, exposed concrete, etc.). Made with special resins and additives it reduces the absorption of the support while allowing the necessary transpiration, uniforms the absorption making the application of the finishing coats easier. It always works in depth, which is why it is the ideal preparation for applying water-based paints or coatings. Adhesion is excellent even on particularly difficult surfaces, thanks to the use of special resins and the presence in the formulation of an adhesion promoter interacting between the support and the product. Preliminary treatment of any surface (civil, plaster, rustic, dry mortars, plasterboard, concrete, prefabricated, exposed concrete etc.) designed to isolate the support surfaces and standardise the absorptions of the subsequent anti-condensate treatments (painting and protective coatings). Packaging: 14-liter bucket UM: €/l

PROTEX is an excellent quality emulsion paint for interior and exterior use, with great hiding power and exist the 10 basic colour. It’s suitable for the colour mix of plastic and acrylic paints. It’s suitable for plaster, concrete, bricks and wood. It has great working and levelling properties, strong adhension and quick drying. It gives a beautiful mat finish. Information: Emulsion paint based on P.V.A-VEOVA copolymer. Applycating with brush, roller or airless and thinning with 5-10% clean water. The spreading rates are 9-12m²/Lt. on previously prepared surfaces. It drying normally on touch after 1-2 hours and recoatable after 3 hours. Times make different under cold or dump conditions PACKAGE:0,17 LT, 0,375 LT, 0,75 LT, 10 LT, 3 LT COLOR:Black, Blue

COMPOSITION ET ASPECT Blanche. CONDITIONNEMENTS Cartouche de 290 ml. STOCKAGE 12 mois à l’abri du froid et des fortes chaleurs en emballage d’origine non entamé. CARACTÉRISTIQUES TECHNIQUES • Matières premières : MS Polymère • Système de durcissement : par l’humidité • V itesse de durcissement : 2,5 à 3 mm par 24 h. (à T=23°C et 50 % HR) • Formation de peau : 10 à 15 minutes (à T = 23°C et 50 % HR) PRÉCAUTIONS D’EMPLOI Ne pas travailler en dessous de +5°C. Conserver hors de portée des enfants. Contient : N-(3-(trimethoxysilyl)propyl)ethylenediamine - Bis(1,2,2,6,6-pentamethyl-4-piperidyl) sebacaat - Methyl1,2,2,6,6-pentamethyl-4-piperidyl sebacaat. Peut déclencher une réaction allergique. PRÉPARATION DES SUPPORTS Les supports doivent être propres, secs, dépoussiérés et dégraissés. APPLICATION Appliquer la colle en extrudant un cordon ou des points sur le support ou l’élément à coller. Assembler les matériaux le plus vite possible : maxi 10 minutes. • Poids spécifique...

Coating for the decoration and protection of all kinds of exterior masonry surfaces with a mineral appearance. Suitable for application as a thin coat paint or as a thick coating capable of filling microcracks in the substrate, levelling surface imperfections and restoring single coat mortars on facades. Prevents fungal and algae growth and surface tensions. Maintains the appearance of the surface by providing durability, dirt repellency, water repellency, weather resistance, thermal insulation and durable colours with sunlight resistance. Paint with a coating protect that provides an excellent protection against a wide range of fungus and algae.

Protech AC-P Paint based on acrylic resins in aqueous emulsion, for interiors and exteriors, protective lamellar structure which, in addition to having an aesthetic effect, allows maximum filling, transpiration and very high resistance to mechanical and chemical light. The high coverage and expandability make this product extremely easy to apply. The special acrylic resins that compose it allow to obtain a film characterized by a rapid insensitivity to water even during the drying phase, with a consequent reduction of the "snail effect" in the event of atmospheric events. Protective and decorative finish painting of walls, facades, concrete products, plasters, masonry, natural stone, porous substrates in general. For old plasters, pay particular attention to the old pre-existing paints, which must be removed by careful scraping and brushing in order to obtain a healthy and non-friable support; then proceed with the application of Protech Fix AC fixative. When applying on new plasters, it is good practice to insulate the base with acrylic insulator or even better with a white or neutral microemulsion fixative. Avoid windy or cold days when applying. Do not apply on fresh or particularly alkaline substrates, respect a minimum carbonation period of at least four weeks. On large surfaces it is recommended to apply product from the same batch and always proceed wet on wet to avoid signs of recovery. Never operate with temperatures below + 5 ° C. Rainy weather, excessive atmospheric humidity and temperatures below + 8 ° C can greatly compromise drying with the possibility of washing off by rainwater even after several days. . DILUTION (by volume with drinking water) BRUSH 1st COAT: 15% a crossed coat or two coats 12-24 hours apart 2nd COAT: 10%. ROLLER 1st COAT: 10% 2nd COAT: 10%. SPRAY (through specific equipment) 1st COAT: 15/25% 2nd COAT: 15/25%. To avoid filming defects, being resin-based products in aqueous emulsion, the application temperature must be between + 5 ° C and + 35 ° C with relative humidity not higher than 60/70%. Do not apply under the direct action of the sun and wind. Do not apply on fresh or particularly alkaline substrates, respect a minimum drying period of the substrate of at least four weeks. It is also advisable for colored, not to use on large surfaces dyed with different production batches as slight differences between batch and batch are technically possible. Please check the color before application as we will not respond to any disputes regarding the shade of the applied product. From 0.20 to 0.30 liters of Protech AC-P for each square meter of surface to be painted. Pail 14 l

Waterbased pigmented primer for all types of masonry substrates. Suitable even on fresh concrete and mortar. Features Excellent adhesion to concrete. Excellent alkali and efflorescence resistance. Excellent water resistance. Good UV resistance. Interior and exterior. Eco friendly. Solvents free. Ready for use, do not dilute.

2component epoxy paint for the protection of concrete floors, metal structures, etc. Does not contain solvents (100% solids). Features Excellent adhesion. Great penetration power. Good adhesion in wet substrate with high percentage of humidity. Good capacity for reaction at low temperatures and high percentage of humidity. Indoor and outdoor use.

DÉFINITION TECHNIQUE Enduit décoratif à projeter en pâte prête à l’emploi pour un usage en murs et plafonds intérieurs. Permet de rattraper dans une certaine mesure les défauts du support tels que bullages et balèvres. Peut être appliqué en tant qu’enduit de lissage ou en relief structuré type « gouttelette ». Différentes teintes et qualité lavable sur demande. DOCUMENTS À CONSULTER DTU 59.1. PV CSTB N°R.A.97.179 : classement au feu MO. COMPOSITION ET ASPECT Résine acrylique en émulsion, charge minérale, dérivés cellulosique, agent de conservation et divers adjuvants. La pâte est de couleur blanche et de consistance adaptée à la projection mécanique. CARACTÉRISTIQUES TECHNIQUES • Extrait sac : 72% • Densité : 1,6 SUPPORTS ADMIS Béton plus ou moins bullé, béton brut de décoffrage, béton cellulaire, carreaux de terre cuite, première couche lissée de SOLIDECOR, agglos, enduits plâtre, anciennes peintures, enduit ciment, carreaux de plâtre, plaques de...

TECHNICAL DEFINITION CE 78 PERFECT’LIGHT is a lightweight ready-mix paste specially formulated for jointing mitred-edge plasterboards in association with plaster tape. COMPOSITION AND APPEARANCE Resin, water, calcium carbonate, lightweight fillers, preservation agent and various adjuvants. The paste is white. COVERINGS. Plasterboard primer. Smoothing filler. REFERENCE DOCUMENTS • CE marking • DTU 25.41 and DTU 25.42 • NF EN 13963 • DoP PACK SIZE 20 kg buckets on covered pallet. STORAGE 12 months in original unopened packaging away from frost and high temperatures. APPLICATION Before actual jointing, fill any accidental gaps between boards and any other areas (spalls, deterioration of the surface etc.). Apply manually by «buttering» the mitred-edge using a 10 or 15 cm plaster spatula and then adding the tape Then add a finishing coat, allow to dry and finish to hide the tape. Also hide the screw heads. For projecting vertical edges, use reinforced tape.